StarTech.com PM1115P2 Manual de instrucciones

Manual Revision: 01/23/2014For the most up-to-date information, please visit: www.startech.comDE: Bedienungsanleitung - de.startech.comFR: Guide de l&

Instruction Manual87. In the setup wizard, select an already congured printer from the list, click Next, Next and then Finish to complete the instal

Instruction Manual910. Make sure the Use the following port radio-button is clicked and select LPT1: (recommended Printer Port) from the pull-down lis

Instruction Manual1011. Select Manufacturer and Printer from the lists of printer drivers. Then click Next. 12. If you already have the printer’s driv

Instruction Manual1115. Click Start -> Devices and Printers and highlight your newly installed printer.

Instruction Manual1216. Right-click, select Printer Properties, then the Ports tab and verify that the print server’s port appears.

Instruction Manual1317. Select the General tab and click Print Test Page to verify the conguration. Note: If you want to install more print servers,

Instruction Manual14Mac OSTo use the print server in Mac OS (10.2 and up), no software installation is required. The necessary conguration can be don

Instruction Manual158. The print server should automatically display in the default list. Select it, then click the “Use” drop-down and click Select

Instruction Manual16OperationPSAdmin Application (Windows)After the software has successfully been installed, you can start the PSAdmin utility from y

Instruction Manual17Print servers discovered on the LAN will be displayed along the top portion of the window, with their respective Device Name, MAC

Instruction ManualFCC Compliance StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Instruction Manual18Setup WizardThe Setup Wizard is a conguration program that can assist you in setting up the necessary parameters for your print s

Instruction Manual19NetWare 1. Log into your NetWare le server as a Supervisor (Admin) or equivalent and run PSAdmin.2. Click the Wizard button fro

Instruction Manual20Advanced Setup (Device Properties)The device properties screen oers several tabs with advanced conguration options. 1. Select t

Instruction Manual21TCP / IP TabChoose either “Obtain an IP address from DHCP server” if there is a DHCP server on your network. Or “Specify an IP add

Instruction Manual22NetWare TabPrint Server Name: Type in the Print server that was created using PCONSOLE.Bindery Settings (Optional): Select NetWare

Instruction Manual23Multiple Print Queues CongurationTo congure the print server to service multiple print queues, please follow the instructions li

Instruction Manual24Firmware UpgradeUpgrade allows you to upgrade the print server device, in the event that a new rmware becomes available.Note: Mak

Instruction Manual25To access the web console:1. Open your browser and enter the IP address of the print server in the address bar of your web browse

Instruction Manual26System TabAllows you to congure basic system settings. Click the Save & Restart button to apply any changes made.Email Alert:

Instruction Manual27Printer TabAllows you to congure settings related to the connected printer. Click the Save & Restart button to apply any chan

Instruction Manual1Table of ContentsIntroduction ... 2Packagi

Instruction Manual28TCP/IP Settings: Choose either “Obtain TCP/IP settings automatically (use DHCP/BOOTP)” if there is a DHCP server on your network.

Instruction Manual29NetWare TabAllows you to congure NetWare related settings for the print server. Click the Save & Restart button to apply any

Instruction Manual30AppleTalk TabAllows you to congure AppleTalk related settings for the print server, to accept jobs from Mac workstations using th

Instruction Manual31SNMP TabAllows you to congure Simple Network Management Protocol (SNMP) related settings for the print server. A host on the netw

Instruction Manual32When an unusual condition or activity occurs, the SNMP agent alerts the SNMP manager through SNMP traps. The following list summar

Instruction Manual33SMB TabAllows you to congure Server Message Block (SMB) printing. Click the Save & Restart button to apply any changes made.W

Instruction Manual34Factory DefaultTo reset the unit to factory default settings, click the OK button on this screen and conrm your choice.Firmware U

Instruction Manual35Restart SectionThe Restart Section allows you to save all changed settings and restart the print server. Click OK to perform the r

Instruction Manual36Print jobs are sent to the print queue successfully, but fail to be sent to the printer1. The Print server Name/Print Q ueue

Instruction Manual37SpecicationsNumber of Ports 1Interface / Bridge ParallelIndustry StandardsIEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TXConnector(s)

Instruction Manual2IntroductionPackaging Contents• 1x Parallel Print Server • 1x Power Adapter • 1x Software CD • 1x Quick Start GuideSystem Requi

Instruction Manual38Technical SupportStarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solut

Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.StarTech.com is your one-stop source for every connectivity part you need.

Instruction Manual3Product OverviewLED IndicatorsLED State IndicationStatus Blinking for POST (Yellow)When power is connected, the Status indicator wi

Instruction Manual4Reset ButtonReboot the Print Server: 1. Verify the power of print server is turned on. 2. Press the reset button once, and then r

Instruction Manual5Software InstallationWindows1. To enable network communication with print server, your computer must have a proper IP address, e.g

Instruction Manual65. From the “Select A Print Sever” screen, select the print server that you want to congure and click Next.

Instruction Manual76. Click “Yes, I want to change settings”, then click Next to congure the IP settings of the print server to match your network.