StarTech.com 410VDSLEXT2 Manual de instrucciones

Manual Revision: 12/18/2014For the most up-to-date information, please visit: www.startech.comDE: Bedienungsanleitung - de.startech.comFR: Guide de l&

Instruction Manual6Pin 4 - General ProtectionOFF: If Pin 4 is in the OFF position, the Transmitter Unit will operate with a SNR ratio up to 9 dB.ON: I

Instruction Manual7CongurationWeb InterfaceThe Receiver Unit has a built-in web interface for conguring the settings. There is no software installat

Instruction Manual8SystemAuthentication CongurationChange your login name and password in this area. Press the “Update” button to save your changes.

Instruction Manual9Load Default SettingProvides two methods to restore the 410VDSLEXT2 to default settings.1. Reserved IP: Allows you to reload the d

Instruction Manual10Conguration Backup/ RestoreTo create a backup of your settings, click the “Download” button and a pop-up will display, letting yo

Instruction Manual11Port ManagementPort CongurationSet port congurations and select which ports to apply these settings to. Select all four ports to

Instruction Manual12Port MirroringChoose to mirror congurations using two settings, click on “Change Mirror Mode” button to change your mirror setup

Instruction Manual13Bandwidth ControlSet bandwidth control on individual ports. Select the port that you wish to control, and then enter the Tx and Rx

Instruction Manual14CRC CounterDisplays the number of CRC errors while the 410VDSLEXT2 is active. Click the “Clear” button to reset the counter and th

Instruction Manual15Tag Base VLANSelect “Tag Base” from the “VLAN Mode” using the “Change Mode” button as need.In Setup Area 1, you can choose the VLA

Instruction ManualFCC Compliance StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Instruction Manual16QoS SettingPriority ClassicationEnable QoS function based on the selected priority mode. If you need to start QoS function, pleas

Instruction Manual17Port-Based PriorityTwo items should be selected in order to set this priority up.1. Port number: Choose the port number you wish

Instruction Manual18TOS/DSCP PriorityYou can assign a queue with a DSCP priority. Click on the “Submit” button and the information will be saved and u

Instruction Manual19Security FilterMAC ID FilterFive MAC addresses can be stored in the “MAC ID Filter”. Choose which entry number you wish to save th

Instruction Manual20Specic IP Address: Choose which entry you wish to add this set of data. In this mode, you need to provide specic IP addresses. C

Instruction Manual21Mode SelectIn this section, you must set the Receiver to CO (Central Oce), or CPE (Customer Premises Equipment) operating modes.

Instruction Manual22Connector Architecture Ethernet Ports The RJ45 Ethernet Port interface is an 8-pin modular jack. The table below displays the pino

Instruction Manual23Resetting Your DeviceThere is a reset button on the rear of the 410VDSLESXT2 Receiver Unit. Please use a narrow item such as a pen

Instruction Manual24

Instruction Manual25Technical SupportStarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solut

Instruction ManualiTable of ContentsIntroduction ... 1Packagi

Instruction Manual26

Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.StarTech.com is your one-stop source for every connectivity part you need.

Instruction Manualii

Instruction Manual1IntroductionPackaging Contents• 1x 1 Port VDSL2 Ethernet Transmitter • 1x 4 Port VDSL2 Ethernet Receiver• 2x Universal Power Ada

Instruction Manual2DC InputLED IndicatorsLED IndicatorsRJ11/RJ45 VDSL Line PortRJ11 VDSL Line PortRJ45PortsDC InputResetReceiver UnitTransmitter UnitD

Instruction Manual3LED DisplaysTransmitter UnitLAN LED DisplayLED Blinking ON OFF1 Activity Link up Link down2 100 Mbps 10 Mbps3 Full duplex Half dupl

Instruction Manual4Installation Hardware Installation Transmitter Unit1. Connect the provided power adapter from an AC electrical outlet to the DC In

Instruction Manual5DIP Switch Settings - TransmitterThe Transmitter Unit has a 4-position DIP switch for conguration of Side, Channel, Rate Limit, an